News

a325 high strength bolt weights

Image

187 Structural Bolt Weight Chart

2022 2 24 nbsp 0183 32 ASTM A325 Bolt Strength ASTM A325 bolt strength are summarized in the table bellow inluding tensile strength yield strength and hardness etc Notes The stress area is calculated as follows As 0 7854 D 0 9743 n As stress area in 2 D nominal bolt size and n threads per inch 2014 7 25 nbsp 0183 32 ASTM A325 high strength bolts Fluted steel decking spanning 12 5 supports reinforced light weight concrete slabs Shear studs connect the slabs to the steel frame for composite action Approximately five months after the building frame was completed in April 1998 the noise occurrences began The

Image

ASTM A325M Boltport Fasteners

This calculator can be used as an aid to help estimate the weight of bolts nuts and washers We provide it as a resource for our customers because the weight of a bolt or assembly is often needed when calculating shipping costs or jobsite delivery requirements 2020 10 29 nbsp 0183 32 Bolts are typically supplied as plain or hot dip galvanized in diameters from 1 2 to 1 1 4 and lengths to 8 Fully threaded bolts are available thread to head in lengths up to four times the diameter All of these bolts are heat treated to a minimum tensile strengh of 120 KSI up to 1 diameter and 105 KSI over 1 A325 STRUCTURAL BOLTS TYPE III

Image

A 325 HEAVY HEX A 325 HEAVY HEX STRUCTURAL BOLTS STRUCTURAL BOLTS

2017 1 25 nbsp 0183 32 ASTM A325 F3125 Structural bolts steel heat treated 120 105 ksi minimum tensile strength The ASTM A325 specification covers high strength heavy hex structural bolts from 1 2 diameter through 1 1 2 diameter These bolts are intended for use in structural connections and therefore have shorter thread lengths than standard hex bolts 2011 5 2 nbsp 0183 32 Length Weight of ASTM A325 or A490 high strength bolts Under Head Heavy Hex Structural Bolts with Hex Nut in Pounds Kg per 100 Inches mm 1 2 quot 13 5 8 quot 16 3 4 quot 19 7 8 quot 22 1 quot 25 1 1 8 quot 29 1 1 4 quot 32 1 3 8 quot 35 1 1 2 quot 38 1 quot 25 16 5 7 48 29 4 13 34 47 21 32 1 1 4 quot 32 17 8 8 07 31 1 14 11 49 6 22 5 74 4 33 75 104 47 17

Image

ASTM F3125 A325 Precision Bolts

38행 nbsp 0183 32 Weight lbs per hundred ASTM F3125 Grade A325 or A490 heavy hex structural bolts Bolt Diam F C H Weight lbs Width Across Flats Width Across Corners Thickness Basic Max Min Max Min Basic Max Min 1 ⁄ 2 7 ⁄ 8 0 875 0 850 1 010 0 969 31 ⁄ 64 0 504 0 464 0 07 5 ⁄ 8 1 1 ⁄ 16 1 062 1 031 1 227 1 175 39 ⁄

Image

Structural Bolts ASTM A325 amp ASTM A490 AALL AMERICAN

2012 2 24 nbsp 0183 32 High Strength Bolt An ASTM A325 or A490 bolt an ASTM F1852 twist off type tension control bolt or an alternative design fastener that meets the requirements in Section 2 8 Inspector The party responsible to ensure that the contractor has satisfied the provisions of this Specification in the work Joint All high strength bolts washers and nuts were made of ASTM A325 high strength steel with the yield stress Fy of 620 MPa and the ultimate stress Fu of 800 MPa The weight and price of SMA material used for each model is presented in table 4

Image

ASTM F3125 Grade F1852 A325 TC Precision Bolts

2021 3 26 nbsp 0183 32 ASTM A325 Fasteners Manufacturer in India The ASTM A325 specification covers high strength heavy hex structural bolts from 1 2 quot diameter through 1 1 2 quot diameter These bolts are intended for use in structural connections and therefore have shorter thread lengths than standard hex bolts Weight lbs per hundred ASTM F3125 Grade A325 or A490 heavy hex structural bolts with a nut Above weights are for plain finish bolts with nuts Hot dip galvanizing will add less than one half of one percent gt 0 5

Image

ASTM A325 Powered by Portland Bolt

Directions Enter values for bolt type A325 or A490 bolt diameter whether threads are included N or excluded X from the shear planes the number of bolts in the connection whether the connection is designed as quot slip critical quot the 2020 10 29 nbsp 0183 32 Bolts are typically supplied as plain or hot dip galvanized in diameters from 1 2 to 1 1 4 and lengths to 8 Fully threaded bolts are available thread to head in lengths up to four times the diameter All of these bolts are heat treated to a minimum tensile strengh of 120 KSI up to 1 diameter and 105 KSI over 1 A325 STRUCTURAL BOLTS TYPE III